Americas

United States United States
Canada Canada
Mexico Mexico
Brazil Brazil

Europe

United Kingdom United Kingdom
Germany Germany
Italy Italy
France France
Switzerland Switzerland
Spain Spain
Sweden Sweden
Russia Russia

Asia Pacific

Australia Australia
China China
Hong Kong Hong Kong
Japan Japan
Singapore Singapore
Taiwan Taiwan
South Korea South Korea
India India
close
Search:
 

Welcome, Misfit.


HOW DO SPRING BARS WORK?

Spring bars can be installed on your device to hold sport, leather and field straps. Either end of the sping bar can be depressed in using your finger or fingernails. When the ends of the spring bars are depressed, the overall length of the bar will be shorter. This allows the spring bar to be installed between watch lugs.

To install spring bars:

Place one end of of the spring bar in the small hole on the inside of the lug.
Using your fingernail, depress in the opposite end of the spring bar to make the bar shorter. Insert the end of the spring bar into the small hole on the inside of the lug.
 
 

To remove spring bars:

Using your fingernail, depress in one end of the spring bar to make the bar shorter and (simultaneously) pull that end away from the lug.
Pull the opposite end of the spring bar out of the small hole.
 
 

HOW DO I CHANGE BUCKLES ON 20 mm STRAPS?

You can easily remove or install buckles using the quick-release spring bar on most 20 mm straps.

To remove a buckle:

Locate the quick-release knob on the inside of the strap. To release the buckle, the knob will need to be pushed in (towards the middle of the strap).
Using your fingernail, push the quick-release knob in (towards the middle of the strap).
Hold the quick-release knob in and (simultaneously) pull the the end buckle away from the strap.
 

To install a buckle:

Locate the quick-release knob on the inside of the strap. Place the far end of the spring bar, opposite of the quick-release know, in the small hole inside the buckle. To install the buckle, the knob will need to be pushed in (towards the middle of the strap).
Using your fingernail, push the quick-release knob in (towards the middle of the strap). You should see the spring bar shorten in length.
Hold the quick-release knob in and (simultaneously) slide the other end of the buckle into position. When you let the knob go, the spring bar should slide into the small hole on the inside of the buckle.
 

HOW DO I CHANGE SPORT OR LEATHER STRAPS?

You can easily remove or install sport or leather straps by using the buttons on the inside of each strap. If you are using a Misfit Vapor or Command device, you will need a 20 mm spring bar pre-installed on the lugs of your device. If you are using a Misfit Phase device, you do not need a spring bar.

Most 20 mm straps are compatible with Misfit Phase, Command and Vapor. The images below depict how to change straps on a Misfit Vapor device, but the same instructions would also apply to Misfit Phase and Command.

To remove straps:

Flip the device over. You should see two buttons on each end of each strap.
Using your fingertips and nails, lift strap flap up and away from under the buttons.
The buttons should be able to pop out of the holes in the flap. Peel back the flap.
Remove the strap from under the spring bar.

Remove the opposite strap using the same steps. Using your fingertips and nails, lift strap flap up and away from under the buttons.
The buttons should be able to pop out of the holes in the flap. Peel back the flap.
Remove the strap from under the spring bar.
 

To install straps:

Flip the device over, so that the back of the product is facing up towards you.
Slide the flap of the strap (near the two buttons) under the spring bar.
Fold the flap up and over the spring bar. Align the two holes on the flap over the two buttons. Using two fingers, press down around one hole to pop the button through.
 

Using two fingers, press down around one hole to pop the second button through.
 
Install the opposite strap using the same steps. Slide the flap of the strap (near the two buttons) under the spring bar.
Fold the flap up and over the spring bar. Align the two holes on the flap over the two buttons. Using two fingers, press down around one hole to pop the button through.

Using two fingers, press down around one hole to pop the second button through.
 
 
 

HOW DO I USE FIELD STRAPS?

The field strap covers up the back of the Vapor, which disables the heart rate sensor. 20 mm field straps are compatible with Misfit Phase, Command and Vapor (heart rate disabled). If you are using a Misfit Vapor or Command device, you will need a 20 mm spring bar pre-installed on the lugs of your device. If you are using a Misfit Phase device, you do not need a spring bar.

The images below depict how to use field straps on a Misfit Command device, but the same instructions would also apply to Misfit Phase and Vapor.

To use field straps:

If you are using a Misfit Vapor or Command device, 20 mm spring bars must be installed on the lugs of your device.
Pull the up on the long strap material in the center of the field band.
Continue pulling up on the strap material until it’s completely out from under the metal strap keeper.
 

Insert the long strap material over the spring bar and behind the device.
 
Pull the end of the long strap material behind the device and over the second spring bar. Pull the strap material through as far as possible.
Slide the end of the long strap back under the metal strap keeper.

Pull the long strap through the metal strap keeper as far as possible.
 
 
Side view of properly installed field band.